172,51 kr
FRI frakt: Tisdag, 18 maj på beställningar över 229,00 kr som skickas av Amazon.
Prioriterad leverans: Måndag, 17 maj
Beställ inom 44 min
I lager.
Din transaktion är säker
Vi jobbar hårt för att skydda din säkerhet och integritet. Vårt säkerhetssystem för betalningar krypterar din information under överföringen. Vi delar inte dina kreditkortsuppgifter med tredjepartssäljare, och vi säljer inte din information till andra.
Fraktas från och säljs av Amazon.
Har du denna produkt och vill sälja den?

Wolfcraft 4640000 Dowel Master, Grå

4,6 av 5 stjärnor 9 610 betyg

Pris: 172,51 kr
Nytt (3) från 172,51 kr och FRI frakt på beställningar över 229,00 kr
Dowelmaster

Förbättra ditt köp

  • För 6, 8 och 10 mm stift
  • Universell och snabb dämpning jigg
  • För brädtjocklekar från 12 - 30 mm
  • För hörn, T-rumpa och kant-till-kanter anslutningar

Produktinformation

Stil:Dowelmaster

Teknisk information

Ytterligare information

Feedback


Köps ofta tillsammans

  • Wolfcraft 4640000 Dowel Master, Grå
  • +
  • Wolfcraft 2755000 Djupstopp, 3 delar, Silver
  • +
  • Wolfcraft Ankarfäste ø8 mm, 4 Stycken
Totalt pris: 241,93 SEK
Köp de valda objekten tillsammans

Har du en fråga?

Hitta svar i produktinformationen, frågor och svar samt i recensionerna.

Det uppstod ett problem med att slutföra din förfrågan. Försök med din sökning igen senare.
Alla Produktinformation Kundfrågor och svar Kundrecensioner

Din fråga kan besvaras av säljare, tillverkare eller kunder som har köpt den här produkten.

Se till att du publicerar i form av en fråga.

Ange en fråga.

Produktbeskrivning

Stil:Dowelmaster

Wolfcraft - Monteringsguide för trä. Det är en snabb och universell ankarstyrning för vinklade, T-formade och passande ytor. Här är den tekniska informationen: - för 6, 8 och 10 mm tidskrifter - för brädor 12 till 30 mm tjocka - förpackning: dubbelblister 2910000.


Kundens frågor och svar

Kundrecensioner

4,6 av 5 stjärnor
4,6 av 5
9 610 övergripande betyg
Hur beräknas betyg?

Inga kundrecensioner från Sverige

Det finns 0 recensioner och 1 kundbetyg från Sverige

Populäraste recensionerna från andra länder

Margie
5,0 av 5 stjärnor Better way to use this jig?
Granskad i Storbritannien den 3 juni 2020
Stil: DowelmasterVerifierat köp
Kundbild
5,0 av 5 stjärnor Better way to use this jig?
Granskad i Storbritannien den 3 juni 2020
Several reviewers have commented that it is difficult to hold this jig steady especially when doing the first drilling into the end of your wood or panel. Several complaints about the jig moving slightly and the dowels not being quite vertical. The trouble is we might have been watching the wrong You Tube video, the English version where you clamp the wood vertically and try to drill down for into the wood while trying to hold the jig firm and steady at the same time which is very difficult. By accident I came across a Spanish video where the wood is clamped horizontally or at a slight upward slope towards the user and then you drill from the front. Assuming most of us are using the 8 mm dowels you can now use your weight pushing down on the handle of the jig and at the same time pushing forward with your thumb to keep the jig pressed squarely and firmly against the edge the the edge of the wood. You are also drilling forward which is slightly more comfortable than drilling down. Try this method and see what you think - I am sure like me you will find it to be a better and easier way. EDIT : having used this jig quite extensively on 18 mm melamine faced boards to make kitchen units here are my further comments. The first picture shows my inclined workmate raised about 2 inches at the front. This was easier than making an inclined ramp on my fixed workbench. It is weighted down by a heavy tool box which is also pushed hard up against a scrap piece of MDF to make the workmate really firm and solid. The MDF is just hung on the the workmate frame with a couple of cup hooks and is easily removable. The second picture shows me using the dowelmaster. You will see that I am not only bearing down on the handle to make sure the dowel enters the centre of the panel but also pushing with my thumb to make sure the jig remains square on to the board. The drill is a very old 300 watt Black & Decker which is not too heavy and does the job fine. You will notice it will be easier to remove build of wood chips when you are drilling your 28 mm hole as the exit path for the chippings is now almost horizontal rather than being vertical. The blue pads off cuts of these silicone type non slip mats. Even with strong clamps I found that because the melamine surface is so slippy there was a tendency for the board to move when pushing hard on the drill. The last picture is a few tips which you might find useful. I had to think of some easy way to provide depth stops to drill 28 mm into edges but only 14 mm into faces of boards. In my odds and end boxes I came across these black nylon spacers which were unused bits from fixing a wall mounted TV bracket and they have a 8 mm hole. The larger ones are 15 mm high and the smaller ones are 5 mm high. Using steel washers as well I can make up any length drill stop. The red one I use for drilling 28 mm edge holes and I just add the blue one to it as well to reduce the drilling depth to 14 mm for face drilling. The adavantage of these spacers are that they are very cheap and the nylon will not cause any wear on your jig. The other thing I noticed is that when the spacer stops spinning you have drilled down to the correct depth! You might be wondering why there is a piece of green and yellow earthing tape stuck on the top corner of the jig. Well I noticed that this angle was almost exactly over where the dowel hole is made in the edge. So if you want to be more precise where you put your dowel holes then just line up the middle green line over where you want your dowel! I was not impressed with the video recommending that you move the board 40 mm, using a ruler, when making T joints. I could see looking down the holes that I was a little bit out. I decided to use instead to use the raised edge on the side of the dowel master. The trouble is that it is grey plastic on grey plastic so not easy to line up. Just rub the edge with white chalk and blow off the excess and now makes lining up really easy. Last thing. I strongly recommend the 50 mm long confirmat screws in between your dowels if you can't glue your joints, which you can't easily do with melamine boards.
Bilder i den här recensionen
Kundbild Kundbild Kundbild
KundbildKundbildKundbild
59 människor tyckte detta var till hjälp
Rapportera missbruk
Matteo B.
3,0 av 5 stjärnor Senza infamia né gloria, adatta solo per hobbisti e per lavori leggeri
Granskad i Italien den 12 december 2017
Stil: DowelmasterVerifierat köp
101 människor tyckte detta var till hjälp
Rapportera missbruk
Phil
4,0 av 5 stjärnor A clever design
Granskad i Storbritannien den 13 december 2018
Stil: DowelmasterVerifierat köp
23 människor tyckte detta var till hjälp
Rapportera missbruk
Bredon House
5,0 av 5 stjärnor Excellent
Granskad i Storbritannien den 9 november 2018
Stil: DowelmasterVerifierat köp
9 människor tyckte detta var till hjälp
Rapportera missbruk
She & Me
5,0 av 5 stjärnor Der absolute Wahnsinn
Granskad i Tyskland den 26 november 2018
Stil: DowelmasterVerifierat köp
34 människor tyckte detta var till hjälp
Rapportera missbruk